Skip to content

Free quotes and a return visit once we install

(972) 962-9846
(972) 962-9846

ServicesPatio Doors

Patio Doors in Murphy, TX

We replace worn sliding and hinged patio doors with new units set plumb on a flashed sill, so the panel glides easily, the lock lines up and hot air stays outside. After the install, we check back and show you how to keep the track clean.

Installer in a cap and jeans fits a white-framed sliding glass patio door panel into its frame on a covered brick back patio, with a ladder and tool bag nearby

When It Makes Sense to Replace a Patio Door

No other opening in the house moves this much glass each day. Rollers that grind, panels that no longer close at the interlock and fog between the panes tend to appear at once, since those parts wear at about the same pace. Replacing the whole unit renews them all in a single visit.

We put in sliding doors, French doors and single hinged patio doors in vinyl, fiberglass or aluminum-clad frames. All of them use tempered insulated glass, and a low-E coating with argon fill reduces the sun's heat through south- and west-facing panes during a North Texas summer.

The trim going on is not the end of our job. After the door has had some daily use, we return to make sure the panel still runs straight, and we show you the easy upkeep that keeps the track and weatherstripping working.

What Comes With Your Installation

Taking out the old door with care
We pull the old frame and panels while keeping disturbance to the drywall or brick around them as small as possible. Once the opening is bare, the framing and subfloor are exposed for the first time in years.
Flashed sill pan
Most patio door leaks start at the sill, not at the glass. We put a sloped sill pan under the new frame so any water that gets under the threshold runs back outside instead of into the subfloor.
Frame set level, plumb and square
We shim the frame at the hinge or roller points and check it in both directions. Even a well-made door will drag on its track and gap at the interlock if the frame is out of square.
Insulating and sealing the outside
We fill the gap between the frame and rough opening with low-expansion foam that will not bow the frame. Around the outside, we use a sealant suited to your siding or brick.
Hardware, trim and a clean finish
We tune the hinges or rollers, place the strike so the mortise or multipoint lock catches cleanly, and put up the interior trim. The old door leaves with us, and we vacuum the floor before going.

Signs It's Time to Replace Your Patio Door

  • Sliding it is a workout

    Rollers worn flat and an aluminum track with grooves cut into it let the panel ride low and drag. When the track is the worn part, new rollers rarely bring back an easy glide.

  • Cloudy glass you can't wipe clean

    A failed edge seal lets moist air into the insulated glass unit, leaving haze between the panes. By the time you see it, the gas fill that slowed heat transfer has already escaped.

  • Air or daylight where the panels meet

    A draft or a sliver of light at the interlock points to flattened weatherstripping or a racked frame. Over time, a slab shifting in clay soil can twist a frame out of square.

  • Damage at the threshold

    Flooring that feels soft, laminate starting to lift or stained wood next to the sill means water is getting under the frame. A new door with proper sill flashing should go in before the damage spreads.

  • The latch needs a nudge

    When you have to lift or shove the panel before it will catch, the latch and keeper have drifted apart. At that point the lock no longer secures your home the way it was designed to.

What Sets the Cost of Your Patio Door

No two openings are quite alike, so we give a number only after measuring yours and seeing how the existing frame sits in the wall. The options you pick account for most of the total. The only real unknown is the condition of the wood beneath the old sill, which we can't see until it's removed.

Size and panel layout

A two-panel slider is the most economical configuration. Adding a third or fourth panel raises the cost, and French doors with two working panels need extra hinges and hardware.

Frame material

Vinyl is the budget-friendly choice. Fiberglass resists warping and fading better when a west-facing wall takes the afternoon sun, while aluminum-clad wood costs the most and gives you real wood on the inside.

Glass options

Each upgrade adds to the total: low-E coatings, argon fill, grids, decorative glass and blinds enclosed between the panes.

What's under the old frame

Rotted subfloor or framing from a past leak has to be cut out and rebuilt before the new door goes in. We photograph the damage and price the repair for you before we touch it.

Resizing or restyling the opening

Switching from a slider to French doors, or widening the opening, may call for new framing and a new header, plus drywall and trim work inside.

The Steps of a Patio Door Job

  1. 1

    Visit to your home

    We measure the rough opening, see how the current frame sits, and go over sliding or hinged styles, frame materials and glass. Your written quote lists every item.

  2. 2

    Placing the order

    Each patio door is made to the measured size, so we order after you sign off on the quote. When it arrives, we tell you and pick an install day together. If your address needs a permit, we pull it.

  3. 3

    The day we install

    We protect the floors, take out the old door, check the opening and set the new unit with flashing, shims, foam and sealant. A single patio door is usually done in one working day.

  4. 4

    Walkthrough and return check

    Before leaving, we have you work the door yourself and show you how to clean the track, keep weep holes open and use silicone lubricant instead of oil. Later we come back to make sure it still slides and locks like it did the first day.

Window technician kneels beside a homeowner, pointing at a window on the side of a brick house, with a ladder, drill, caulk gun and tool bag on the lawn

Patio Door Questions We Often Get

Should I pick a slider or French doors?

A slider moves inside its own frame, so it works well when furniture sits close to the glass. French doors open across the full width and usually seal tighter, because they close against compression weatherstripping and lock with a multipoint latch. During the consultation we measure the swing clearance and help you compare them.

Will a new door fit my existing opening?

In most cases. Each unit is built to the rough opening we measure, so a same-size replacement leaves the wall framing alone. If you want a different size or style, we explain the framing work involved before you choose.

Does a new patio door have a warranty?

Yes. Every patio door we install comes with a limited lifetime warranty on labor and product, and it transfers to the buyer if you sell. We go over the coverage when we review your quote.

Can I pay over time?

Yes. We offer $0 Down on the whole project and 0% Financing options. Ask about them when you call for your free quote.

What happens if something gets damaged during the install?

We are fully insured. Replacing a patio door means removing one heavy tempered glass panel from the wall and setting a new one, and our insurance protects you if anything goes wrong.

How do I keep a new patio door working well?

Vacuum the track every few weeks so sand and grit don't wear the rollers, and keep the weep holes in the sill open so water can drain. Wipe down the weatherstripping and look over the exterior sealant once a year. We show you all of this before we leave and check back afterward.

Two-story tan brick house with new black-framed windows still bearing stickers, a stepladder, boxes and a drill by the front porch and shrubs

Ready for a Door That Glides Again

Tell us which door is giving you trouble and we'll come measure it. You'll get a written quote and a clear picture of the options before you decide anything.